| SubAssy | Category | Item | Thumbnail | Part Name | Part Description | Make/Buy | QTY | Included in kit? | Comment | Vendor | Vendor URL | |||||
| OPTION 1 - WOBBLEX | ||||||||||||||||
| ZR_V2.6 | Buy | 1 |
|
WobbleX WS12 Isolators | WobbleX WS12 for SFU12 12mm ball screws | Buy | 3 | YES | This is the
best option. While allowing a thinner dimesion to maximize Z travel distance,
these metal pieces will not bend under the bed weight and enclosure higher
temperatures. This kit contains all pins and ball bearing for the printed parts of your build. |
Mellow 3D Official Store | https://s.click.aliexpress.com/e/_DBAJHXh | |||||
| OPTION 2 - Printed Wobble Rings | ||||||||||||||||
| ZR_V2.6 | Make | 2 |
|
ZR2.6_WobbleRing_Printed_RH | Printed Wobble Ring Right | Make | 1 | NO | Make sure to
use a material that is not prone to creep. ABS-CF and ASA-CF are good candidate. Avoid Nylon/PA. |
HevORT | https://github.com/MirageC79/HevORT/tree/master/files/STL/ZR_V2.6 | |||||
| ZR_V2.6 | Make | 3 |
|
ZR2.6_WobbleRing_Printed_LH_RR | Printed Wobble Ring Left and Rear | Make | 2 | NO | Make sure to use a material that is not
prone to creep. ABS-CF and ASA-CF are good candidate. Avoid Nylon/PA. This part will fit for Left hand ball screw and rear ball screw. |
HevORT | https://github.com/MirageC79/HevORT/tree/master/files/STL/ZR_V2.6 | |||||
| ZR_V2.6 | Hardware | 4 |
|
Dowell Pin 3mm Dia X 15mm long | Dowell Pin 3mm Dia X 15mm long | Buy | 48 | NO | Tool steel is better than stainless. Much more resistant to wear. | AliExpres | https://s.click.aliexpress.com/e/_DmKB2wj | |||||
| ZR_V2.6 | Hardware | 5 |
|
Ball Bearing 6mm | Ball Bearing | Buy | 12 | NO | High carbon steel | AliExpres | https://s.click.aliexpress.com/e/_DFhdrQB | |||||
| ZR_V2.6 | Hardware | 6 |
|
Magnet, 8mm dia X 3mm thick | Magnet, 8mm dia X 3mm thick | Buy | 12 | NO | Rare Earth Magnets N35 | AliExpres | https://s.click.aliexpress.com/e/_DlKZKZ1 | |||||
| REGULAR PARTS - Items identified with ZR_V2.5 and ZR_V2.6 are common between the two version. They can be reused in case of upgrading from 2.5. Watch for comments in case of QTY increase | ||||||||||||||||
| ZR_V2.5 ZR_V2.6 |
Buy | 7 |
|
BedSquare | 2020 Extrusion | Buy | 1 | NO | See required
Dimension as per Frame Calculator https://github.com/MirageC79/HevORT/tree/master/docs/assets/references/frame |
|||||||
| ZR_V2.5 ZR_V2.6 |
Buy | 8 |
|
BedSpring_20mm | 20mm Spring | Buy | 4 | YES | Commonly available (same springs as most printers) | |||||||
| ZR_V2.5 ZR_V2.6 |
Buy | 9 |
|
SFU1204-450(-3)* With Nut | Ball Screw
with 22mm diameter Nut |
Buy | 3 | NO | BK10 and BF10
machined end required. BK10 and BF10
blocks ARE NOT required. Length 450mm
fits Z axis of 340mm. *Nut cylindrical portion should have a diamerter of 22mm Some supplier will Identify as -3. Length determined by Frame Calculator: https://github.com/MirageC79/HevORT/tree/master/docs/assets/references/frame |
AliExpress | https://s.click.aliexpress.com/e/_DdCsRNX | |||||
| ZR_V2.5 ZR_V2.6 |
Buy | 10 |
|
Ball Bearing 608RS | Bearing 608RS or 608ZZ | Buy | 3 | YES | AliExpress | https://s.click.aliexpress.com/e/_DC2F1d9 | ||||||
| ZR_V2.5 ZR_V2.6 |
Buy | 11 |
|
Bearing_5200-2RS | Double Angular Contact Bearing | Buy | 3 | YES | AliExpress | https://s.click.aliexpress.com/e/_DDCKfSX | ||||||
| ZR_V2.5 ZR_V2.6 |
Buy | 12 |
|
Ruland_57445K444_CLAMPING SHAFT COLLAR (MCL-10-F) | Shaft Collar, 10mm ID | Buy | 3 | YES | Ruland | https://www.ruland.com/mcl-10-f.html | ||||||
| ZR_V2.5 ZR_V2.6 |
Buy | 13 |
|
Coupler D20L25-5.0-8.0 | Coupler, Spider - 5mm to 8mm | Buy | 3 | YES | AliExpress | https://s.click.aliexpress.com/e/_DlGaJ2X | ||||||
| ZR_V2.5 ZR_V2.6 |
Buy | 14 |
|
MGN12H_150MM | MGN12 Rail with H Block | Buy | 3 | YES | ||||||||
| ZR_V2.5 ZR_V2.6 |
Buy | 15 |
|
MGN12H_Rail Assy | MGN12H Rail - For Z | Buy | 3 | NO | See required
Dimension as per Frame Calculator https://github.com/MirageC79/HevORT/tree/master/docs/assets/references/frame |
|||||||
| ZR_V2.5 ZR_V2.6 |
Buy | 16 |
|
BedPlate | MIC6 Aluminum 6mm thickness | Buy | 1 | NO | See required Dimension as per Frame
Calculator https://github.com/MirageC79/HevORT/tree/master/docs/assets/references/frame |
Mic 6® a registered trademark of
Arconic Alca 5™ a registered trademark of PCP Aluminum Alpase K100-S® is a registered trademark of TST, Inc (Flatness not equal) Vista Metals ATP 5™ is a registered trademark of Vista Metals Corp Alimex ACP 5080™ is a registered trademark of Alimex, Germany. Formodal 030™ is a registered trademark of Bikar Metal in Germany. Thanks to Steven Kleinert for the info. |
||||||
| ZR_V2.5 ZR_V2.6 |
Buy | 17 |
|
POS8_RodEnd | RodEnd, POS08 | Buy | 3 | YES | Note: You may
want to buy a few extra if ordering from AliExpress as level of precision of
the bearing can vary. You can also puch the brass liner slightly to correct excessive play. |
AliExpres | https://s.click.aliexpress.com/e/_DBMc6uJ | |||||
| ZR_V2.5 ZR_V2.6 |
Buy | 18 |
|
NEMA17 1.8 degree Stepper Motors 60 mm* | Stepper Motor - NEMA17X60mm | Buy | 3 | NO | *It is recommended to use 60mm 1.8 degree motors to avoid the bed falling down due to backdriving | |||||||
| ZR_V2.5 ZR_V2.6 |
Hardware | 19 |
|
M3_Nut_94150A325 | Nut, Hex - M3 | Buy | 12 | YES | ||||||||
| ZR_V2.5 ZR_V2.6 |
Hardware | 20 |
|
M4_Nut_94150A335 | Nut, Hex - M4 | Buy | 9 + 3* | YES | * ZR_V2.5 was using 3 M4 nuts per ball
screw. 3 Additional Required for ZR_V2.6 |
|||||||
| ZR_V2.5 ZR_V2.6 |
Hardware | 21 |
|
M8X1.25_HexNut_90593A007 | Nut, Hex - M8X1.25 | Buy | 6 | YES | ||||||||
| ZR_V2.5 ZR_V2.6 |
Hardware | 22 |
|
M5X2020_T-Nut_91239A224 | Nut, T-Slot - M5 for 2020 profile | Buy | 26 | YES | Any type is ok, make sure to have a few roll in (drop in) T-Nut under hand | |||||||
| ZR_V2.5 ZR_V2.6 |
Hardware | 23 |
|
M3X3030_TSlot_Nut | Nut, TSlot - M3X3030 | Buy | 24 | YES | NOTE: Qty 24 based on Z Print size at 340. Add Qty3 for every additional 5cm of Z axis over 340mm. | |||||||
| ZR_V2.5 ZR_V2.6 |
Hardware | 24 |
|
M5X3030_TSlot_Nut | Nut, TSlot - M5X3030 | Buy | 6 | YES | Any type is ok, make sure to have a few roll in (drop in) T-Nut under hand | |||||||
| ZR_V2.5 ZR_V2.6 |
Hardware | 25 |
|
M6_TSlot_Nut | Nut, T-Slot - M6 for 3030 profile | Buy | 15 + 6* | YES | Any type is
ok, make sure to have a few roll in (drop in) T-Nut under hand * ZR_V2.5 was using 15. 6 Additional are required for ZR_V2.6 |
|||||||
| ZR_V2.5 ZR_V2.6 |
Hardware | 26 |
|
M5X10_ButtonHeadScrew_97763A820 | Screw, ButtonHead - M5X10mm | Buy | 26 | YES | ||||||||
| ZR_V2.5 ZR_V2.6 |
Hardware | 27 |
|
M5X12_ButtonHeadScrew_91239A228 | Screw, ButtonHead - M5X12mm | Buy | 6+3* | YES | * ZR_V2.5 was using 6. 3 Additional are required for ZR_V2.6 to lock the 5200 bearings down. | |||||||
| ZR_V2.5 ZR_V2.6 |
Hardware | 28 |
|
M6X12_ButtonHeadScrew_92095A227 | Screw, ButtonHead - M6X12mm | Buy | 16 + 9* | YES | * ZR_V2.5 was using 16. 9 Additional are required for ZR_V2.6 | |||||||
| ZR_V2.5 ZR_V2.6 |
Hardware | 29 |
|
M3X10_CapScrew_92290A115 | Screw, Cap - M3X10mm | Buy | 50 | YES | ||||||||
| ZR_V2.5 ZR_V2.6 |
Hardware | 30 |
|
M3X12_CapScrew_92290A117 | Screw, Cap - M3X12mm | Buy | 12 | YES | ||||||||
| ZR_V2.5 ZR_V2.6 |
Hardware | 31 |
|
M3X8_CapScrew_92290A113 | Screw, Cap - M3X8mm | Buy | 12 | YES | ||||||||
| ZR_V2.6 | Hardware | 32 |
|
M4X16_CapScrew_90348A015 | Screw, Cap - M4X16mm | Buy | 12 | YES | Qty 4 per Ballscrews. To attach WobbleX lower ring to the Ballscrew Nut | |||||||
| ZR_V2.5 ZR_V2.6 |
Hardware | 33 |
|
M8X35_CapScrew_90605A257 | Screw, Cap - M8X35 | Buy | 1* | YES | *You can use Qty 3 X M8X35 on this version. | |||||||
| ZR_V2.5 ZR_V2.6 |
Hardware | 34 |
|
M8X30_CapScrew_91290A434 | Screw, CapScrew - M8X30 | Buy | 2* | YES | *You can use Qty 3 X M8X35 on this version. | |||||||
| ZR_V2.5 ZR_V2.6 |
Hardware | 35 |
|
M4X40_FlatHead_93395A277 | Screw, FlatHead - M4X40mm | Buy | 4 | YES | ||||||||
| ZR_V2.6 | Make | 36 |
|
ZR_V2.6_MotorMount_FL | Motor Mount Front Left | Make | 1* | NO | *ZR_V2.5 part equivalent is fully interchangeable and can be used in lieu of this ZR_V2.6 version. | HevORT | https://github.com/MirageC79/HevORT/tree/master/files/STL/ZR_V2.6 | |||||
| ZR_V2.6 | Make | 37 |
|
ZR2.6_SliderMount_FL | Slider Mount Front Left | Make | 1 | NO | Not interchangeable with ZR_V2.5 | HevORT | https://github.com/MirageC79/HevORT/tree/master/files/STL/ZR_V2.6 | |||||
| ZR_V2.6 | Make | 38 |
|
ZR2.6_BearingTopMount_FL | Bearing Top Mount Front Left | Make | 1* | NO | *ZR_V2.5 part equivalent is fully interchangeable and can be used in lieu of this ZR_V2.6 version. | HevORT | https://github.com/MirageC79/HevORT/tree/master/files/STL/ZR_V2.6 | |||||
| ZR_V2.6 | Make | 39 |
|
ZR_V2.6_MotorMount_FR | Motor Mount Front Right | Make | 1* | NO | *ZR_V2.5 part equivalent is fully interchangeable and can be used in lieu of this ZR_V2.6 version. | HevORT | https://github.com/MirageC79/HevORT/tree/master/files/STL/ZR_V2.6 | |||||
| ZR_V2.6 | Make | 40 |
|
ZR2.6_SliderMount_FR | Slider Mount Front Right | Make | 1 | NO | Not interchangeable with ZR_V2.5 | HevORT | https://github.com/MirageC79/HevORT/tree/master/files/STL/ZR_V2.6 | |||||
| ZR_V2.6 | Make | 41 |
|
ZR2.6_BearingTopMount_FR | Bearing Top Mount Front Right | Make | 1* | NO | *ZR_V2.5 part equivalent is fully interchangeable and can be used in lieu of this ZR_V2.6 version. | HevORT | https://github.com/MirageC79/HevORT/tree/master/files/STL/ZR_V2.6 | |||||
| ZR_V2.6 | Make | 42 |
|
ZR_V2.6_MotorMount_RR | Motor Mount Rear | Make | 1* | NO | *ZR_V2.5 part equivalent is fully interchangeable and can be used in lieu of this ZR_V2.6 version. | HevORT | https://github.com/MirageC79/HevORT/tree/master/files/STL/ZR_V2.6 | |||||
| ZR_V2.6 | Make | 43 |
|
ZR2.6_Slider_Mount_RR | Slider Mount Rear | Make | 1 | NO | Not interchangeable with ZR_V2.5 | HevORT | https://github.com/MirageC79/HevORT/tree/master/files/STL/ZR_V2.6 | |||||
| ZR_V2.6 | Make | 44 |
|
ZR2.6_BearingTopMount_RR | Bearing Top Mount Rear | Make | 1* | NO | *ZR_V2.5 part equivalent is fully interchangeable and can be used in lieu of this ZR_V2.6 version. | HevORT | https://github.com/MirageC79/HevORT/tree/master/files/STL/ZR_V2.6 | |||||
| ZR_V2.6 | Make | 45 |
|
WobbleRing_SFU1204_FL_LowerDisc | Wobble Ring & WobbleX lower disc. Adapter for 12mm Ball screw SFU12 | Make | 3 | NO | HevORT | https://github.com/MirageC79/HevORT/tree/master/files/STL/ZR_V2.6 | ||||||
| ZR_V2.5 ZR_V2.6 |
Make | 46 |
|
BedPlateMount_RL_Body_V2 | BedPlateMount_RL | Make | 1 | NO | Same as ZR_V2.5 | HevORT | https://github.com/MirageC79/HevORT/tree/master/files/STL/ZR_V2.6 | |||||
| ZR_V2.5 ZR_V2.6 |
Make | 47 |
|
BedPlateMount_RR_Body_V2 | BedPlateMount_RR | Make | 1 | NO | Same as ZR_V2.5 | HevORT | https://github.com/MirageC79/HevORT/tree/master/files/STL/ZR_V2.6 | |||||
| ZR_V2.5 ZR_V2.6 |
Make | 48 |
|
ZR_BedPlateMount_FR_Body_V2 | ZR_BedMountFR_Body | Make | 1 | NO | Same as ZR_V2.5 | HevORT | https://github.com/MirageC79/HevORT/tree/master/files/STL/ZR_V2.6 | |||||
| ZR_V2.5 ZR_V2.6 |
Make | 49 |
|
ZR_BedPlate_InnerBraquet_FL | ZR_BedPlate_InnerBraquet_FL | Make | 1 | NO | Same as ZR_V2.5 | HevORT | https://github.com/MirageC79/HevORT/tree/master/files/STL/ZR_V2.6 | |||||
| ZR_V2.5 ZR_V2.6 |
Make | 50 |
|
ZR_BedPlate_InnerBraquet_FR_Body | ZR_BedPlate_InnerBraquet_FR | Make | 1 | NO | Same as ZR_V2.5 | HevORT | https://github.com/MirageC79/HevORT/tree/master/files/STL/ZR_V2.6 | |||||
| ZR_V2.5 ZR_V2.6 |
Make | 51 |
|
ZR_BedPlateMount_FL_Body_V2 | ZR_BedPlateMount_FL | Make | 1 | NO | Same as ZR_V2.5 | HevORT | https://github.com/MirageC79/HevORT/tree/master/files/STL/ZR_V2.6 | |||||
| ZR_V2.5 ZR_V2.6 |
Make | 52 |
|
ZR_BedRailSupport_RR_Body | ZR_BedRailSupport_RR | Make | 1 | NO | Same as ZR_V2.5 | HevORT | https://github.com/MirageC79/HevORT/tree/master/files/STL/ZR_V2.6 | |||||
| ZR_V2.5 ZR_V2.6 |
Make | 53 |
|
HevORT LOGO_Small_Grey | HevORT Logo, Small | Make | 3 | NO | Best with resin printer | HevORT | https://github.com/MirageC79/HevORT/tree/master/files/STL/ZR_V2.6 | |||||
| ZR_V2.5 ZR_V2.6 |
Make | 55 |
|
ZR Logo Small | ZR Logo Small | Make | 2 | NO | Best with resin printer | HevORT | https://github.com/MirageC79/HevORT/tree/master/files/STL/ZR_V2.6 | |||||
